--- EVA Hot Melt Adhesive Manufacturer | Quanyixintong
---
Adhesive grade guide

EVA Hot Melt Adhesive

EVA medium-temperature grades are 150–180 °C and high-temperature grades are 180–210 °C.

EVA hot melt adhesive grades for edge banding
Product overview

EVA Hot Melt Adhesive: selection and use

EVA hot melt adhesive is available in medium-temperature and high-temperature ranges for edge-banding applications. The confirmed medium-temperature range is 150–180 °C; the high-temperature range is 180–210 °C. These are grade categories, not a substitute for the instructions of a particular adhesive or machine. Always identify the exact grade and follow its technical data sheet, equipment guidance, and safe operating procedures when setting a production line.

Choosing between temperature categories begins with the machine's permitted operating window and the recommendations for the exact grade. Compare those requirements with the actual line, the edge material, the panel, and the process conditions. The setpoint alone is not enough to determine whether a grade is suitable. Provide the machine model, actual production speed, edge-band material and dimensions, panel substrate, and the adhesive application details so the supplier can review the request as a system.

Machine speed can influence the time available for application and bonding, but it should not be used by itself to select adhesive. The customer's operating conditions, substrate, edge material, application equipment, and required result also matter. If the speed changes between product lines, describe each line separately. A sample or grade review should use the intended settings and actual materials; follow the product documentation instead of assuming that the temperature range determines every process parameter.

EVA and PUR are distinct product choices and must not be treated as interchangeable on the basis of a short description. PUR grades are available, and their technical data sheets should guide grade-specific temperature, processing, storage, and handling. Ask for the data sheet that applies to the proposed PUR grade. Do not transfer an EVA setting to PUR or infer PUR behavior from the EVA temperature ranges on this page.

A complete adhesive request identifies the edge-banding material, panel, machine manufacturer and model, line speed, application method, current adhesive if known, and the specific issue or objective. State whether the request concerns a new line, a product change, or a process adjustment. If your machine supplier has defined limits, include them. The supplier can then confirm what grade information is available and which additional details are necessary for a responsible recommendation.

Before a production order, test the selected adhesive with the customer's actual edge banding and panel on the intended line. Record the grade, lot identification, machine temperature settings, speed, and observations according to your internal procedure. Changes to materials or equipment may require another review. Do not assume a universal open time, viscosity, softening point, density, or shelf life; those values are grade-specific and must be confirmed from the applicable product documentation.

For sample planning, indicate the amount needed for your test, the machine and application, destination, and the proposed date of the line trial. Confirm sample format and quantity for the request. The edge-banding MOQ is 3,000 m per color. Standard roll lengths are 100, 150, or 200 m; custom lengths and customer-branded packaging can be requested. Lead time depends on order quantity, with approximately 20 days for one 20GP order. Include these details in the inquiry so the response can pair technical selection with a feasible order plan.

The most reliable selection process is documentation plus a controlled line trial. Start with the confirmed EVA temperature category, submit the machine and process details, obtain grade-specific information, and test using the customer's own materials. For PUR, make the inquiry datasheet-based from the beginning. This approach supports a clear specification without inventing performance claims or assuming that one adhesive is appropriate for every machine, material, or production speed.

Specification table

MaterialEVA
FinishGrade selected for the machine and application
ThicknessNot applicable
WidthNot applicable
EVA medium-temperature range150–180 °C
EVA high-temperature range180–210 °C
PUR gradeAvailable; use the selected grade's technical data sheet.
ViscosityEVA values are listed by grade on the EVA adhesive page; the supplied table does not state the unit.
Softening pointEVA values are listed by grade on the EVA adhesive page.
Open timeTODO_CONFIRM: confirm open time for the requested grade.
DensityTODO_CONFIRM: confirm density for the requested grade.
Shelf lifeTODO_CONFIRM: confirm shelf life for the requested grade.
PackagingTODO_CONFIRM: confirm packaging for the requested grade.
MOQ and lead timeTODO_CONFIRM: confirm MOQ and lead time for the requested grade.

For published EVA grade temperatures, viscosity, softening points, colors, and machine speed ranges, see the EVA grade specification table. Confirm the polymer and grade identity before applying those values.

Applications

  • Edge banding on furniture panels
  • Furniture factories using hot-melt adhesive
  • Production lines requiring grade-specific process confirmation

Matching and production review

Compare the machine's specified range with the selected EVA grade category, then confirm the grade data sheet and run a test with your actual edge banding and panel. For PUR, use only its grade-specific data sheet.

Confirm the proposed material and grade against your panel, process, and acceptance requirements. Test the sample on your own line before approving an order; a catalog description does not replace a production trial or grade-specific technical data.

PUR adhesive by technical data sheet

PUR grades are available for inquiry. Share your machine, line speed, panel and edge-band materials, and application details, then request the technical data sheet for the exact grade. PUR temperature and handling requirements are grade-specific; follow that datasheet rather than applying EVA settings.

EVA grades

EVA hot melt adhesive specifications by grade

Values below are transcribed from the supplied EVA product analysis table. The source does not state the viscosity unit. Confirm units and the current grade-specific technical data sheet before setting a production line. Grade-level operating temperatures may differ from general medium- and high-temperature category ranges listed elsewhere on the site.

Grade Colors Softening point (°C) Viscosity at 180°C Viscosity at 200°C Operating temperature (°C) Speed (m/min) Recommended boards Application listed in source
H-316 Natural, pure white, black 120 ± 5 180,000 ± 20,000 100,000 ± 10,000 180–220 18–50 OSB, Multilayer board, Particle board, Density board, Ecological board Listed as a high-temperature, high-strength, fast-curing grade for high-speed automatic edge banding and various edge-banding materials.
6890 Natural, pure white, coffee 110 ± 5 160,000 ± 20,000 100,000 ± 30,000 180–210 15–40 OSB, Multilayer board, Particle board, Density board, Ecological board Listed for medium and large automatic edge-banding machines and various edge-banding materials.
6860 Natural, pure white, coffee 110 ± 5 150,000 ± 20,000 85,000 ± 20,000 180–210 15–30 Multilayer board, Particle board, Density board Listed for medium and large automatic edge-banding machines and various edge-banding materials.
6820 Natural 120 ± 5 100,000 ± 20,000 65,000 ± 10,000 180–200 15–25 Multilayer board, Particle board, Density board Listed for medium and small automatic edge-banding machines and various edge-banding materials.
S960 White mix 110 ± 5 110,000 ± 20,000 65,000 ± 10,000 180–210 15–40 Ecological board Listed for ecological-board edge banding and cladding, and for wooden doors.
H-313 Natural 90 ± 5 50,000 ± 10,000 30,000 ± 10,000 150–180 15–25 Not specified Listed for manual edge-banding machines and various edge-banding materials.
6871 Natural 85 ± 5 27,000 ± 5,000 15,000 ± 3,000 150–180 10–20 Not specified Listed for manual edge-banding machines and various edge-banding materials.
6831 Natural 84 ± 5 18,000 ± 5,000 9,000 ± 3,000 130–160 15–20 Not specified Listed as a medium-temperature grade for manual edge-banding machines and various edge-banding materials.

The source table lists H-316 speed as 18–50 m/min, while its feature text says 18–80 m/min. The table value is shown here; verify the correct range against the current H-316 technical data sheet. Speed and operating temperature are grade-specific and do not replace the grade data sheet or machine instructions.

Sample request

What to send for a sample

Provide machine make/model, line speed, application method, panel substrate, edge-band material and dimensions, current settings or adhesive if known, destination, and line-trial plan.

Samples are evaluated by the customer on their own production line before an order. Share your observations and any requested adjustments so the final specification can be confirmed.

Request a product sample
Product questions

Frequently asked questions

Which operating temperature should I choose?

Compare the machine's specified operating window with the EVA medium range (150–180 °C) or high range (180–210 °C). Confirm the final settings using the grade data and machine guidance.

Can you recommend a grade from machine speed alone?

Speed is one input, not a complete grade specification. Send the machine model, actual line speed, edge material, panel, and application details so the grade can be reviewed for the complete process.

Can I request PUR adhesive?

PUR grades are available. Request the technical data sheet for the specific grade and follow its storage, handling, and processing requirements.

Related adhesive products

Confirm a specification for your production line

Send your panel, machine, finish, and dimension requirements for review.

Request a Quote Ask on WhatsApp